Best Punch Set With Buying Guide

by
Best Punch Set
Disclaimer: As An Amazon Associate I Earn From Qualifying Purchases.
NoProductScoreAction
1Astro Pneumatic Tool 1600 16-Piece Punch and Chisel Set9.8Buy On Amazon
2TEMCo TH0037 4" HYDRAULIC KNOCKOUT PUNCH Electrical Conduit Hole Cutter Set KO Tool Kit 5 Year Warranty9.6Buy On Amazon
3TEMCo Hydraulic Knockout Punch TH0004 - Electrical Conduit Hole Cutter Set KO Tool Kit 5 YEAR WARRANTY9.2Buy On Amazon
4CRAFTSMAN Center Punch, 3-Piece Set (CMHT82541)9.2Buy On Amazon
5GEARWRENCH 27 Pc. Punch and Chisel Set - 823069.2Buy On Amazon
6Starrett Drive Pin Punch Set8.8Buy On Amazon
7SE 4-Piece Watch Chain Link Remover Punch Pins Set - JT630588.8Buy On Amazon
8Great Eastern Entertainment One Punch Man - Saitama & Genos Pin Set8.4Buy On Amazon
9HORUSDY 16-Piece Punch and Chisel Set8.2Buy On Amazon
10SWANLAKE 16-Piece Punch and Chisel Set8.2Buy On Amazon

Table Of Content:

1. Astro Pneumatic Tool 1600 16-Piece Punch and Chisel Set

Astro Pneumatic Tool 1600 16-Piece Punch and Chisel SetBuy On Amazon
  • Taper Punch: 3/32-Inch By 5-1/4-Inch, 1/8-Inch By 5-3/4-Inch, 5/32-Inch By 6-Inch, 3/16-Inch By 6-1/4-Inch, 1/4-Inch By 6-3/4-Inch.
  • Cold Chisels: 3/8-Inch By 5-1/2-Inch, 1/2-Inch By 6-Inch, 5/8-Inch By 6-1/2-Inch
  • Pin Punch: 3/32-Inch By 4-1/4-Inch, 1/8-Inch By 4-3/4-Inch, 5/32-Inch By 5-Inch, 3/16-Inch By 5-1/4-Inch, 1/4-Inch By 5-3/4-Inch.
  • Center Punch: 1/8-Inch By 5-Inch, 3/16-Inch By 6-Inch

2. TEMCo TH0037 4″ HYDRAULIC KNOCKOUT PUNCH Electrical Conduit Hole Cutter Set KO Tool Kit 5 Year Warranty

TEMCo TH0037 4Buy On Amazon
  • True 13 US ton hydraulic knockout punch with 10 dies.
  • 10 dies for conduit fitting sizes: ½”, ¾”, 1″, 1¼”, 1 ½”, 2″, 2 ½”,3″, 3 ½”, 4″ – Complete kit comes in a rugged storage case with a 5 Year Warranty.
  • Slug splitting designed dies for easy slug removal that leaves a round hole with clean edges and a uniform size is provided on punch sizes ½”, ¾”, 1″, 1¼”, 1 ½” & 2″.
  • Deep Draw dies that are designed with an optimized angle on the cutter face that requires less force to make the cut, reducing operator and tool fatigue is provided on punch sizes 2 ½”,3″, 3 ½” & 4″.
  • Punching Thickness Capacity: 1/8 inch (11 ga) Steel, 1/16 inch Stainless Steel Punches: Steel, Stainless Steel, Brass, Copper, Aluminum (soft alloys only), Fiberglass and Plastic.

3. TEMCo Hydraulic Knockout Punch TH0004 – Electrical Conduit Hole Cutter Set KO Tool Kit 5 YEAR WARRANTY

TEMCo Hydraulic Knockout Punch TH0004 - Electrical Conduit Hole Cutter Set KO Tool Kit 5 YEAR WARRANTYBuy On Amazon
  • Powerful 9 US TRUE TON Punching Capacity.
  • 6 Die Sets for conduit fitting size: ½, ¾, 1, 1¼, 1 ½, 2″
  • Punching Thickness Capacity: 1/8 inch (11 ga) Steel Punching Capacity, 1/16 inch Stainless Steel.
  • Punches: Steel, Stainless Steel, Brass, Copper, Aluminum (soft alloys only), Fiberglass, Plastic
  • 5 Year Warranty from a well-known American name. NON-GENERIC

4. CRAFTSMAN Center Punch

CRAFTSMAN Center Punch, 3-Piece Set (CMHT82541)Buy On Amazon
  • Bi-material grip for comfort and ease of use
  • Flared grips to help protect hands against glancing blow
  • Color coded by tip size for easy identification
  • Hardened Tip for durability

5. GEARWRENCH 27 Pc. Punch and Chisel Set – 82306

GEARWRENCH 27 Pc. Punch and Chisel Set - 82306Buy On Amazon
  • Chisel For Cutting Rivets, Bolts, and Nuts
  • Pin Punch For Final Removal To Drive Out Pins and Rivets
  • Center Punch For Marking Center Lines and Pilot Drill Locations
  • Long Taper Punch To Install and Remove Pins and Shafts and To Align Holes
  • Starter Punch For Both Starting and Installing Pins and Rivets

6. Starrett Drive Pin Punch Set

Buy On Amazon
  • PIN PUNCH USES: Pin punches are tools used to insert or knock out rivets and pins in assemblies They have a metal shank on one end and a metal pin driver on the other and are typically tapped with a hammer.
  • SET OF 8: The Starrett S565WB bulk set includes eight drive pin punches with a 4″ overall length and 1/16″, 3/32″, 1/8″, 5/32″, 3/16″, 7/32″, 1/4″, and 5/16″ pin diameter sizes.
  • STEEL CONSTRUCTION: These pin punches are made of hardened steel for wear resistance and strength.
  • KNURLED GRIPS: Round shank is knurled for a sturdy grip and greater control As an added precaution, always wear safety goggles when using striking tools.
  • STORAGE CASE INCLUDED: This center pouch set comes with a convenient, red plastic storage case for keeping your pin punches organized Each punch has its size stamped on the head.

7. SE 4-Piece Watch Chain Link Remover Punch Pins Set – JT63058

SE 4-Piece Watch Chain Link Remover Punch Pins Set - JT63058Buy On Amazon
  • Sizes (mm): 0.7, 0.8, 0.9, and 1
  • 4 pieces
  • Non-rolling hex body
  • Comes in a pouch for easy storage and transportation
  • Resizes watches

8. Great Eastern Entertainment One Punch Man – Saitama & Genos Pin Set

Great Eastern Entertainment One Punch Man - Saitama & Genos Pin Set, MetalBuy On Amazon
  • Officially licensed one punch Man merchandise
  • Measures 1.5″
  • Collect them all!
  • Limited edition

9. HORUSDY 16-Piece Punch and Chisel Set

HORUSDY 16-Piece Punch and Chisel Set, Including Taper Punch, Cold Chisels, Pin Punch, Center PunchBuy On Amazon
  • Available in 16 different shapes and designs, including: bolt hole alignment, ball head separation, unfolding knuckle, center punch, knockout bolts and pins.
  • Heat treated chromium vanadium provides a high hardness rating that prevents rapid expansion of the head and passivation of the chisel and punch.
  • 5PC Tapered punch: 3/32″ x 5-1/4″, 1/8″ x 5-3/4″, 5/32″ x 6″, 3/16″ x 6-1/4″, 1 /4″ x 6-3/4″ and 3PC Cold Chisels: 3/8″ x 5-1/2″, 1/2″ x 6″, 5/8″ x 6-1/2″.
  • 5PC Punch: 3/32″ x 4-1/4″, 1/8″ x 4-3/4″, 5/32″ x 5″, 3/16″ x 5-1/4″, 1/4″ × 5-3/4″ and 2PC Center punch: 1/8″ x 5″, 3/16″ x 6″.
  • Product material: made of chrome vanadium steel, hardness: 54~58HRC

10. SWANLAKE 16-Piece Punch and Chisel Set

SWANLAKE 16-Piece Punch and Chisel Set, Including Taper Punch, Cold Chisels, Pin Punch, Center PunchBuy On Amazon
  • Available in 16 different shapes and designs, including: bolt hole alignment, ball head separation, unfolding knuckle, center punch, knockout bolts and pins.
  • Heat treated chromium vanadium provides a high hardness rating that prevents rapid expansion of the head and passivation of the chisel and punch.
  • 5PC Tapered punch: 3/32″ x 5-1/4″, 1/8″ x 5-3/4″, 5/32″ x 6″, 3/16″ x 6-1/4″, 1 /4″ x 6-3/4″ and 3PC Cold Chisels: 3/8″ x 5-1/2″, 1/2″ x 6″, 5/8″ x 6-1/2″.
  • 5PC Punch: 3/32″ x 4-1/4″, 1/8″ x 4-3/4″, 5/32″ x 5″, 3/16″ x 5-1/4″, 1/4″ × 5-3/4″ and 2PC Center punch: 1/8″ x 5″, 3/16″ x 6″.
  • Product material: made of chrome vanadium steel, hardness: 54~58HRC